How To Replace A Worn Anti Sway Bar End Link And Bushings ( Honda Accord )




People Who Liked This Video Also Liked

How to Replace a Worn Anti Sway Bar End Link and Bushings ( Honda Accord )
How to Replace a Worn Anti Sway Bar End Link and Bushings ( Honda Accord )
How to Remove and Replace Sway Bar Bushings and End Links - Also Inspection Procedure and Other Tips
How to Remove and Replace Sway Bar Bushings and End Links - Also Inspection Procedure and Other Tips
Honda Accord Sway Bar Bushings Replacement
Honda Accord Sway Bar Bushings Replacement
Sway Bar Link Replacement Honda Acura   Accord   Sway Bar End Links Replacement   TL   CL   Accord
Sway Bar Link Replacement Honda Acura Accord Sway Bar End Links Replacement TL CL Accord
99 - 04 Honda Odyssey Sway Bar End Link Replacement   Install front stabilizer   Bundys Garage
99 - 04 Honda Odyssey Sway Bar End Link Replacement Install front stabilizer Bundys Garage

Did this video help you?

vnappa: I believe the end links are over tightened.
blasting them on with a impact tool is a lazy way to install them.
bushings are not supposed to be distorted

Lionel Rodriguez: Great video. Thanks for the information. RIP Michael.

JOE FORD DIY: MOOG is the way to go if you go after market

Omssini Ltd.: We provide genuine and original power steering rack end bushing products. These are manufactured to repair the rack at the highest quality and standards in our purpose built workshops and then tested using our hi-tech equipment.
http://www.ebay.com/itm/281862205305?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

amazingtweets: Good job!

Tyler Gavett: people make great pets?

RacelineCentral.com: You really don't want to crank them down so hard that the new bushing starts squeezing out like toothpaste. Check your vehicle manufactures requirements for torque amount and go with that. You could cause the bolt to snap while driving if it is torqued beyond specifications.

SpacemanFan1988: When I do these at my dealership I do both sides at the same time to allow more movement from the sway bar itself and makes it much easier to install

cedieboy cedie: i have 1998 accord is the same? sway bar bushing?

David Borough: Holy crap -- how tight did you torque that down? Hope you don't do that to the spark plugs, too!!! :P 2nd on the polyurethane replacements on endlink bushings. But other bushings I personally prefer rubber.

Albinus81: Great video guys - very informative. Not sure about over in the US, but here most people go for aftermarket bushings as they are polyurethane as opposed to the OEM elastic and rubber ones that rot and wear out extremely quickly on our poor roads. Also don't overtighten the new bushings! :)

AutoEclinic: From the description, possibly the axle shafts.

AutoEclinic: How many miles are on your Honda?

Mohammad Iqbal: Hey guys.. awsum video.. I would like to ask a problem with my honda accord 2007. My car is really smooth but sometimes (2/10 times) while driving i can feel a vibration starting and increasing at speed 70+ kmph and eventually the steering will start vibrating really badly and if i apply brakes i can feel some bad vibrations even in the brake pedal. but after some KMs the whole vibrations will go away and the car will be smooth as before.. Can you please let me know what is the issue here..

AutoEclinic: Thank you!

antiard: great! very helpful, thanks!!!
Rating:
How to Replace a Worn Anti Sway Bar End Link and Bushings ( Honda Accord ) 5 out of 5

Featured Video

Refacing Kitchen Cabinets

Latest Comments

vnappa: I believe the end links are over tightened.
blasting them on with a impact tool is a lazy way to install them.
bushings are not supposed to be distorted

Pablo Reinoso: se detiene el proceso com.android.phone al encender  que hago?
Jason L: How many shelves board should I buy? I intend to put A4 size book/files. Will buy the same model in the video.
If I do not mount to the wall, will it be fine?
13:23min what is that model name of the door? I only found square doors.
Thanks

Silva: Muito bom os seus videos,eu estava procurando outra maneira de pintar sem usar cimento,agora achei!
Só acho que a parte de isopor poderia ser lixada pra tirar aquelas marcas de bolinhas...
qual tipo de lixa vc indicaria?

Александр Усов: Бедные студенты...
Marceli6v: thx
Denil Son: does it work the same in CentOS?

How to Replace a Worn Anti Sway Bar End Link and Bushings ( Honda Accord )