Basic Speaker & Amp Wiring/Configuration




People Who Liked This Video Also Liked

Basic Speaker & Amp Wiring/Configuration
Basic Speaker & Amp Wiring/Configuration
4 Channel Amp Install and Speaker Swap - Amplified #144
4 Channel Amp Install and Speaker Swap - Amplified #144
How To Install Amplifier & Subwoofer in Any Car (simple)
How To Install Amplifier & Subwoofer in Any Car (simple)
Car Audio Subwoofers for Dummies: A Basic How-To Installation Guide
Car Audio Subwoofers for Dummies: A Basic How-To Installation Guide
ONKYO Speaker connection - AVR AV Home Cinema Receiver - Bi-Wire Bi-Amp
ONKYO Speaker connection - AVR AV Home Cinema Receiver - Bi-Wire Bi-Amp
How To Install an Amplifier and Subwoofer   How to install speakers
How To Install an Amplifier and Subwoofer How to install speakers
Tip - Banana Plugs into AV Amp Speaker Wire Binding Posts
Tip - Banana Plugs into AV Amp Speaker Wire Binding Posts
Speaker/Amp Wiring - 2006 Honda Civic LX 4dr Sedan Book 1 - Chapter 2
Speaker/Amp Wiring - 2006 Honda Civic LX 4dr Sedan Book 1 - Chapter 2
Behringer X32 - Tri-Amp Speaker Configuration
Behringer X32 - Tri-Amp Speaker Configuration
How to install aftermarket stereo speakers & amp in a Harley-Davidson Motorcycle
How to install aftermarket stereo speakers & amp in a Harley-Davidson Motorcycle
Speaker Wiring 70 Volt Transformer PA amplifier
Speaker Wiring 70 Volt Transformer PA amplifier
Dayton B652 Speakers and Lepai LP-2020A+ Amp unbox. install. and review. by KV5R
Dayton B652 Speakers and Lepai LP-2020A+ Amp unbox. install. and review. by KV5R
Amp Installation Tip: Testing Speaker Wires
Amp Installation Tip: Testing Speaker Wires
Install J&M Audio ROKKER Speakers and Amplifier on HD Ultra Classic • J&P Cycles
Install J&M Audio ROKKER Speakers and Amplifier on HD Ultra Classic • J&P Cycles
How to Install Component Speakers
How to Install Component Speakers
Routing wires for amps and speakers in Camaro Z28 LT1 F Body.
Routing wires for amps and speakers in Camaro Z28 LT1 F Body.
NEW 2013 ONKYO AV RECEIVER TX-NR626 - How to Bi-amp the main speakers
NEW 2013 ONKYO AV RECEIVER TX-NR626 - How to Bi-amp the main speakers
4 Channel Amp Install Tips - Front To Rear Jump
4 Channel Amp Install Tips - Front To Rear Jump

Did this video help you?

Nisiana Koufalis: how about if i run.......2 Speakers & 1 Sub in 1 Amp........... all speakers and sub are 8 ohms.... Amp minimum load is 4 ohms...... what i want to do was connect 2Speaker in parallel......that would give me 4 ohms....to the right channel of the amp.........then plug the 8 ohm sub to the left channel...........does this work?

DJBoz07: thanks mate

crazydevon007: 4 and 8 Ohm Speaker (in parallel) = 1 / (1/8 + 1/4 ) = 2.67 Ohm Load. Not recommended for most amplifiers. in series 12 ohms.

crazydevon007: you would go mixer to active sub (assuming it has a full or high pass output) to amp to top cabs. just like in the video.

djtavi77: awesome!!! but even when your amp says it would support 2ohms, is not recommended to do it, cause it will work too hot, I've heard...

itsj1train: Good job, I thought it was helpfull. Keep it up. Things like this is what helps other djs here on youtube.

djtavi77: we actually need more of this vids in you tube where we learn stuff not just tenminmixes, haha!!! THX a lot.

Ianb: Cant do it!!! i cant listen to you for 10 mins!

DJ Mikey Mike Susca: Nice video good job A+++ Thanks DJ Mikey Mike

Adam Kurimski: There you go guys...it's coming from the man himself! -Adam

Alexis Schmidt: i have peavy 2600 amp. 2 jbl 15 eon and 1 peavy 18 sub cabinet i need to know how to wire these. thanks

chris emanski: approx. 2.66 Ohms per side

bodetyl: what does 4 ohm and 8 ohm make?

Live Productions: One correction: Its actually better for you to bring your laptop volume to only about 75% max because otherwise, A. sometimes you will get more hiss through your system and B. it causes your peak on the gain to come on eariler. This is because the line level is very high and causes more distortion. Using the gain on the mixer is where you want to set your gain volume level.

Robert Crowston: i want to run to (1) 4 ohm sub and (1) 8 ohm top per side through one amp what ohm load is that? thanks rob!

DJBoz07: could you hook things up like following? - DJ mixer > Amp > Active Sub > two L + R 15" PA Speakers? Basically how would I connect my mixer, amp, one sub and two 15" top cabs?? Cheers A C

rockdrummer1226: very helpfull. thanks so much.

Adam Kurimski: I finally understand how that works now...1/(1/ohms+1/ohms+1/ohms...) -Adam

chris emanski: Great vid! Oh and adam, having (3) 8ohms speakers makes a 2.66 ohm load per side, you need 4-8ohm speakers to get it down to 2. Also, lower quality amps can most likely do 4-8 ohms in stereo and 8-16 in bridge mono. QSC, Peavey, Crown amps for example can do down to 2 in stereo and 4 in mono, easily! (in most cases) And altough not recommended, they can handle wierd loads (e.g. 2.66 ohms per side)

patrickman123: -4 ohms i think
Rating:
Basic Speaker & Amp Wiring/Configuration 4.2 out of 5

Featured Video

Refacing Kitchen Cabinets

Latest Comments

Steve Fowler: Car looks okay, but doesn't he look like Jude Law?
L Ys: +koopanique Nah...I think it's from 0:39. But that one sounds damn good too!
MyCookieDeluxe: eigentlich ist das egal, man sollte aber zum arzt gehen und schauen lassen, ob es okay ist sie zu tragen oder eher nicht
Youssef Samaan: Lots of dem are awesome
LPShannah: I'm happy to see that this method worked for many of you! :D If you have any further questions or thoughts about cleaning your LPS, I really suggest you to read the comments on this video. A lot of different people have shared their personal tips and ideas, so you guys should help each other out! :) REMEMBER: This video only shows MY ways on how to clean LPS, and it's worked good for me so far. But when I read the comments I see that I still have a lot to learn! ;D
Jay Grizzle: Can't have Muzzle Breaks in New York anymore.It makes the guns way too dangerous for law abiding, responsible,adults to own.Says the Governor of NY who wants to be your next President.
AeriosDFY2: I could whoop him

Basic Speaker & Amp Wiring/Configuration