DIY 3-D Pantograph Router Copier




People Who Liked This Video Also Liked

Anet A8 - BEST DIY 3D Printer Kit (2016) - Full Review!
Anet A8 - BEST DIY 3D Printer Kit (2016) - Full Review!
COLD AIR INTAKE.  Budget CAI DIY and Review E46 BMW
COLD AIR INTAKE. Budget CAI DIY and Review E46 BMW
Dollar Tree Review and DIY - Fabric Softener & Refresher
Dollar Tree Review and DIY - Fabric Softener & Refresher
Best Cheap DIY 3D Printer Kit Anet A8 - RCLifeOn
Best Cheap DIY 3D Printer Kit Anet A8 - RCLifeOn
BMW E46 Clutch Delay Valve delete DIY and REVIEW
BMW E46 Clutch Delay Valve delete DIY and REVIEW

Did this video help you?

Oscar Lesta: muy bueno chango

Oscar Lesta: you have the measures of the woods?

Oscar Lesta: tienes las medidas de las maderas?

Phillip Evans: Why use background music, especially when it is as bad as this stuff?

Alcides Santtos: Friend, what are the measures and drillings of Pantograph ? I made ​​one for use with the router my original drawing is 14 cm , and the router is copying 3 cm , must have done something wrong , hug !

John Poston: Everyone else was using pins to fasten the pivoting corners... I like your use of hinges (already made rigid pivots!!!).
Thanks...

andrew major: thank you so much, i always over complicat my designs. so whilst i knew the geometry and mech, i designed a beautifly complicated version. but after seeing this i built a beautifully simply version, saved money time and stress. only advice i would give to other builders, is to spent as much of you budget (if very low) on the hinges , the rest is just measuring twice.

Beyond Limits Productions: Nice looking design...and looks doable! Thanks for posting this.I was wondering though on how long that bolt was that was mounted to the back of the rectangle pivot there on top of what looks to be aprx a 3" by 3" piece of plywood.Β 

Austin LaFleur: could you please tell me the demotions of the pieces of wood?

Orlando Martinez: Excelent, thanks,

Marc Van Esch: Do you have a plan for this to do ?

Marc

Fabian Guerrero: hey , very good !! thanks , this is a great idea congrats!!

Wolfgang Palmer: Thanks. I should have showed more of how I did it, but I did not think about it until after the fact.

Wolfgang Palmer: No I sure don't. But the size is not crucial. The important thing is to make it a perfect or 'Golden rectangle, and that the measurements between the hinge points are equal across. The hole for the router depends on YOUR router. You ask a just question though. I should put my plans up, if but to give a starting point to those interested in making a pantograph. Thanks for watching.

Scott Harvey: do you have size drawings for this as i would like to build 1
Rating:
DIY 3-D pantograph router copier 5 out of 5

Featured Video

Refacing Kitchen Cabinets

Latest Comments

Oscar Lesta: muy bueno chango
michelle abney: I'm class of #2K17 and I finally finish paying for my Herff Jones yesterday and now that I have my cap and gown it finally feels like I'm graduating πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“πŸŽ“ #HJGraduation
Nathan Yates: I have a CM7000 and I'm programing it with the OP500. When I get to the special option group 2 settings, the list gives me 1-28 settings. The OP500 only lets me go up to 15. I want to set POC #5 to defrost which is 17. Do you know how to get the OP500 to go past 15? I got the OP500 with my CM4200. Do I need to upgrade to a new firmware? How do I get it?
Mark Borrmann Jr: please change your video title.. there is no night vision camera on this drone... I think you need to look into what night vison cameras are my friend..Β  nice copter though..... infared camera's are usually true night vision as they can see in pitch dark without any light source. they see where you cannot..
larent moscino: only n47 motor is nog good, and alwy probleem with timing
welton santos: eu tenho uma boa imagem e som perfeitos tudo em alta definicao unico problema que eu notei e que ela e meio lenta para ligar demora um pouco.
Haxperten: test

DIY 3-D pantograph router copier