Fishingtuts: This is best fitted with a new garage door. Old doors could bind and the
old springs could have worn out.
CreeperSethT: Woooo chamberlain FTW
idannybo2: My Chamberlain WD832KEV shakes the whole door when it starts the closing
cycle and continues without any shaking. Anybody else seen this problem?
Tekk Savvy: appreciate the info....does the kit include opener brackets---are they
adjustable or standard size (its not under product description)?
Ross Jacobs: Maybe it's time to get a better video camera Chaimberlain DIY
bob smith: that has to be lowest quality garage door opener this brandname puts out..
i have the same one, installed it with no load and the chain hardly
Jason Rodriguez: This video skips some steps on putting the rail together.. I just installed
one and find it easier to put the full rail together first then screw it to
the motor... but great video helped me...
Ed White: useless
thetruth: is it hard to install garage door opener??
Chamberlain: Replacing your #garage door opener? We've got you covered. Learn how with
this step-by-step installation video.
myviews: does the opener carrier come with the garage door or with the door opener?
Andrew Hillman: very UN-informitive
Will whydoihavetoputmylastname: Useless video. You already had everything put together. Lame
Tom F: you did not install the anti close sensors properly.
Anthony notme: Everyone's a professional garage opener installer. Wonder how long it
sceneitb4: Threaded belt the wrong way through rail at first. Didnt mention "hand
tighten" spring assembly first b4 releasing bound spring to exert proper
tension on belt. Lastly, used pliers to hold spring nut? lazy...
Neilfrozn: This would be much more helpful if it were more detailed, slower, and
longer. It moves way too fast to absorb.
Bubba Co: My garage door opening just went kabloooey, and I needed an "in a nutshell"
video to inform me of the general process. I'm a relatively handy guy and
you convinced me that I can most certainly handle the task...thanks!!!
Catherine Dishman: in the instructions they show you different ways to mount the motor unit
using the angle iron. Although some of the methods shown use flat steel
braces that are not included with the unit, which I need for my setup? Also
in this video they show cutting and bending of the angle iron witch is
easier said than done when you only have basic tools
enidradiotesters: Put my first opener up after watching this , but did put my sensors inside
the bracket like the instructions showed. Very good video.
Frank S: You left a lot of steps out that are critical to the installation, position
of the bracket on the front wall, getting the unit level, mounting position
of the bracket to the garage door, etc.
Franco lopez: .. I recommend using and impact drill
soxredsox: wish it was a little more detailed and not freaking 240p smh
7760n: You put the sensor on wrong
TheTexaradoan: I didn't know Newt Gingrich installed garage doors.
GDMafia Quick: Great advertising for a website, but complete useless as instruction to
install a garage door opener.
St8Solja: What about for 2 door opener?
bmason4ever: I am going to get a chambberlain this Friday and this is going to help me
put it together
KPMcWill: It would be beneficial to explain the importance of using reinforcement on
the garage door where you attach the bracket for the trolly arm. There was
no mention of it, just a half second clip showing the bracket attached to
Edwin Garza: Not a good DIY video. Give us the extended video of the installation!
kevinwang05: does the package com with the spring?
Joe Spellman: Sensor should go inside the bracket Dean!
vientodepaz: thank you very much. this video help me.
Ashish Gupta: too fast, useless
LegionCommander: Great video thx for the info!
Striped Bass: looks so easy.
Scott Temonia: Thanks!
Carlos Aguilar: This is not 100% complete. Not good for beginers.
Phil Abrian: Would it be easier to do this when the garage door down?. Not a very good
mohr cowbell: Higher resolution please
How to Install a Chamberlain Garage Door Opener3.6
out of 5