Make A Cyclone Dust Separator - The Cone (part 2 Of 3) (home Made Cyclone)




People Who Liked This Video Also Liked

Shop Vac Cyclone Separator Review - 3 Years Later
Shop Vac Cyclone Separator Review - 3 Years Later
Make a Cyclone Dust Separator - The Top Hat (part 1 of 3) (home made cyclone)
Make a Cyclone Dust Separator - The Top Hat (part 1 of 3) (home made cyclone)
Dust FX 2HP Cyclone Dust Collector Review
Dust FX 2HP Cyclone Dust Collector Review
Make a Cyclone dust separator - The cone (part 2 of 3) (home made cyclone)
Make a Cyclone dust separator - The cone (part 2 of 3) (home made cyclone)
Make a Cyclone dust separator - The test (part 3 of 3) (home made cyclone)
Make a Cyclone dust separator - The test (part 3 of 3) (home made cyclone)

Did this video help you?

Munk E. Punch: duct tape the cone in place while riveting

Anexism: The sealant you used, what's it called? Also, how well does it stand up to the constant barrage of dust hitting it?

Angel Vega: Very Nice job Abraham. I liked.

michaelsway359: Hi Jord, I like the how too on this but I am unable to get to the plans. Keep getting a 404 not found error. Any chance i can get them??

mushtaq mirza: Nice work well done I like it. Thanks but I have a question if I want to make by my size so what is the formula to cut round? Thanks again Mushtaq Mirza uae

РОМАН СМОЛЯКОВ: Суперррр!

Ted Weddell: Tape the joint together before drilling for the rivets. ;)

Bruce Bochicchio: Same here; link to plans is not working.

Paul Gustar: trying to download plans using the link & all i get is your website with the code 404 Not found & the message "No Results Found
The page you requested could not be found. Try refining your search, or use the navigation above to locate the post." Please help..

SuperBardley: Jordan, great video series.  Your narration and edit techniques are succinct and to the point -- good stuff and thank you so much for your generous share!!

Suggestion to save steps, simplify, and improve strength:  at ~ 3:56, you start cutting off the tabs.  In typical HVAC installs, the tradesmen will KEEP those tabs in order to fasten the cone (in this case) or the sheet metal ring in the top hat to the top hat's MDF flanges/plates. So, simply bend them outwards to 90 degrees, apply a generous bead of sealant, and staple or screw (use 3/4" self-drilling sheet metal screws) them into the face of the MDF top hat.

If you cut out the hole for the cone w/ a jig-saw whose base has been set to the same angle as the cone, then you can simply drop and seal (here, construction adhesive would seal and secure the cone to the MDF) the cone directly into the top hat; one could also bend the tabs over and fasten those into place w/ the screws.  One could also use this same technique to attach a short straight pipe section to the bottom of the cone which would provide a connection point for clamping on a short piece of flex that makes an easy on-off w/ the waste bin.

Enrique Lavayen: Jord first of all thanks for the videos and keep them coming! Nice job!

Link for plans is broke "Error 404 Not Found" says. Could you share the dimensions for the cone? Just height and both radius Please!

Thanks and again GREAT job!

Bob Bobbie: I used to install vinyl siding so I still have a metal break. next time you make a cone, find a metal break and bend over edges on the joining section of the cone that can lock together and then just be hammered flat for permanent attachment. This will also give a much tighter air secure connection.

telosfd: Oh yeah i gonna "buy" one from the next street. Thanks.

JordsWoodShop: As much as I would like to say I sat down and did all the geometry, I based the sizing off of commercially available units

Frank Spillman: Jord, how did you go about sizing your cone? Just copied a commercial one, or some gee whiz calculation? Looks good so far!

JordsWoodShop: thanks, Ill give it a shot next time

JordsWoodShop: Yes Bondo is the same thing

Bike Man Dan: Thanks for the videos. Haven't heard of builders bog before. Is it like Bondo?
Rating:
Make a Cyclone dust separator - The cone (part 2 of 3) (home made cyclone) 5 out of 5

Featured Video

Refacing Kitchen Cabinets

Latest Comments

lilyisalizard: Can I just use pritt-stick haha? Halloween is tomorrow!
OPY PRODUCTIONS: Yes, look into sacred geometry
The Littlest Giant: Lmao, look how oversized Todd's suit is. Wtf.
Ринат Валитов: Лучше ДАСТЕРА взять и по асфальту быстрее будет .
HeeroYuyZero13 aka_Aku: Funny because the same thing happened to WoW steam Diablo 3 and many others I play on PC and consoles but I'm not going to deny the facts on the other side
xMoggey: Fnatic got rekt xD
luggage12345: The Nokia 5800 has Kinetic Scrolling and dedicated music shortcuts, also expandable for up to 16 and this only up to 8gb. The nokia 5800 comes with 8GB memory card, AV TV out cable, stand, case etc. The 5800 offers 640x360 nHD quality video. The 5800 has a better battery life and also has a proximity sensor that by just tilting the device you can silence calls and snooze alarms. And most of all now offers free lifetime Ovi maps turn-by-turn GPS navigation up to 74 countries with walk and traffic

Make a Cyclone dust separator - The cone (part 2 of 3) (home made cyclone)